cnc

G82:Single Peck Drilling with Dwell

Submitted by staff member on Thu, 04/09/2015 - 20:25

SYNTAX

G90/G91...G98/G99...G...X...Y...Z...R...P...Q...F...K...

G81:Single Peck Drilling

Submitted by staff member on Wed, 04/08/2015 - 10:01

SYNTAX

G90/G91...G98/G99...G...X...Y...Z...R...P...Q...F...K...

Rectangular Pocketing

Submitted by staff member on Mon, 04/06/2015 - 17:53

SYNTAX

G172   P.. Q.. R.. X.. Y.. Z.. I.. J.. K..
G173   I.. K.. P.. T.. S.. R.. F.. B.. J.. Z..

Circular pocket

Submitted by staff member on Sun, 04/05/2015 - 00:50

SYNTAX

G170 P.. Q.. R.. X.. Y.. Z.. I.. J.. K..
G171 P.. T.. S.. R.. F.. B.. J..

G68:Code For Axis Rotation

Submitted by staff member on Thu, 04/02/2015 - 18:09

SYNTAX

G91 G68  I.. J.. R..

G91     INCREMENTAL
G68     AXIS ROTATION
I,J       CENTRE POINT OF ROTATION
R        ROTATION

NOTE:G69 AXIS ROTATION CANCEL

G54:Coordinate Shift

Submitted by staff member on Thu, 04/02/2015 - 10:07

SYNTAX

G54...X...Y...

Profile

M98:Part repetition

Submitted by staff member on Thu, 03/26/2015 - 22:26

SYNTAX

M98 P000 0000(Subprogram Call)

⇒In P First 3 Digits Means No. Of Reputability
⇒Last 4 Digits Means Subprogram No.   
⇒At Maximum We Can Run The Program 999 Times
⇒Maximum No Of Sub Programs In A Program  Are 9999 Times.

G92:Simple Threading Cycle

Submitted by staff member on Sat, 03/21/2015 - 12:34

SYNTAX

G92 X… Z…F…

Where
X    CORE DIAMETER
Z    LENGTH OF THREAD 
F    FEED RATE(EQUAL TO PITCH VALUE)

NOTE:TOOL POSITION DISTANCE IS ALWAYS EQUAL TO PITCH VALUE IN Z AXIS.

G74:Fast peck Drilling Cycle

Submitted by staff member on Fri, 03/20/2015 - 01:51

SYNTAX

G74  R..
G74  X..Z..Q..F..

Where
R    RETRACTION
X    DIAMETER
Z    LENGTH
Q    PECKING VALUE IN Z AXIS (MICRONS)
F    FEEDRATE

G81:Deep Hole Drilling Cycle

Submitted by staff member on Fri, 03/20/2015 - 01:27

SYNTAX

G81  X...Z...F...

Where
X  Diameter
Y  Length
F  Feed rate

Threaded Fastener

Submitted by Ankit Pathak on Thu, 03/19/2015 - 18:59

INTRODUCTION

A threaded fastener is a discrete piece of hardware that has internal or external screw threads. They are usually used for the assembly of multiple parts and facilitate disassembly.

G02 & G03:Circular interpolation

Submitted by staff member on Thu, 03/19/2015 - 11:05

Circular interpolation commands

G02 CIRCULAR INTERPOLATION CLOCKWISE
G03 CIRCULAR INTERPOLATION ANTICLOCKWISE

Profile

G75:Grooving Cycle

Submitted by staff member on Thu, 03/19/2015 - 10:07

SYNTAX

G75...R...
G75...X..Z...P... Q...F...

where

G94:taper facing cycle

Submitted by staff member on Wed, 03/18/2015 - 22:05

SYNTAX

G90 X....Z....R...F

G94:Simple facing cycle

Submitted by staff member on Wed, 03/18/2015 - 20:59

SYNTAX

G94...X...Z...F

Pages

Subscribe to RSS - cnc

Who's new

  • ravirajpatil871...
  • shubhambajoria
  • yassir
  • demiholyman890954
  • scottgillum51169040

Get Notified

 

Share

We are Social

Syndicate

Subscribe to Syndicate